Showing results: 1066 - 1080 of 2628 items found.
-
ET250 -
Klein Tools, Inc.
The ET250 voltage and continuity tester incorporates an LCD display, measures AC/DC voltage up to 600V and can test GFCI protected circuits. Both voltage testers have a tough meter design and are rated CAT IV 600V for safety.
-
Luna Innovations Inc.
Test and characterize modern optical components, including photonic integrated circuits (PICs) and silicon photonics, with unmatched speed, precision and accuracy. Accelerate and improve your design or optimize your production with Luna’s suite of component analyzers and testers.
-
Scanner -
Square Wheel Industries, Inc.
A Scanner Trailer Lighting System Tester makes the job a lot faster and easier since it powers your trailer's lighting circuits in sequence. You check the operation of all lighting functions in a single walk-around instead of two or three.
-
T&R Test Equipment Ltd.
Our primary current injection test sets cover from 750A through to 6000A. Available in single phase, testing applications include testing and timing of under and over current relays, circuit breakers and CT ratio testing.
-
J2110A -
PICOTEST Corp.
While it is possible to obtain high quality injection transformers with bandwidths as wide as 1Hz to 5MHz or more, in some cases this is still insufficient for some tests. For example a typical heater control loop might have a bandwidth of less than 1Hz while some linear regulators and opamp circuits can have bandwidths of up to 100MHz or in some cases even higher. For these applications, a solid state injector can provide the necessary bandwidth. A solid state injector can perform at DC, while the upper frequency limit is dictated by the components selected and the printed circuit board material and layout. It is possible to obtain a solid state injector with a working range of DC – 200MHz, though above 50MHz the interconnection between the injector and the circuit being tested can become quite critical. It is essential that ripple from the injector power supply does not dramatically degrade the dynamic range or the signal to noise ratio of the measurement. The resulting plots are often much cleaner when using a solid state injector than with a transformer injector.
-
Sat40a II Series -
Amperis sl
The Coil Analyzer SAT40A II series is a powerful tool for testing circuit breakers where a substation battery is not available. It is unique device in the market due to its dual purpose: - It can be used as a stable power supply for coils and spring-charging motors (both DC and AC power supply voltage) during commissioning and maintenance testing. - It is powerful analysis tool for assessing conditions of circuit breaker auxiliary circuit and coils. The Coil Analyzer SAT40A II series has separate DC and AC coil outputs for power supply of opening and closing coils. The output voltage is selectable in the ranges from 10 V to 300 V DC or from 10 V to 250 V AC. The Coils outputs can withstand up to 15 A current. The DC and AC motor outputs can generate from 10 V to 300 V DC and 250 V AC voltage. The motor outputs can withstand starting (inrush) currents up to 40 A. These outputs can also be used as continuous power supply outputs.
-
Shanghai Guantu Technology Co., Ltd.
The lightning wave impulse current generator is an impulse current generator that generates a simulated lightning current waveform . Its working process is as follows: first, the transformer charges the capacitor bank through the silicon pile, when the charging voltage reaches a predetermined value, the spark gap is triggered, and the capacitor is discharged through the total inductance and total resistance of the circuit. When the resistance is greater than or equal to the critical damping value, a unidirectional impulse current wave is generated in the circuit. When the resistance is less than the critical damping value, an oscillating impulse current wave is generated. The magnitude of the impact current amplitude is related to the circuit parameters. When the capacitance value and charging voltage are the same, the smaller the inductance value, the greater the current amplitude. In order to obtain as much current as possible, a pulse capacitor with a small inductance value is usually selected, and the total length of the connecting line should be as short as possible when arranging the main capacitor, so that the total loop inductance value can be reduced as much as possible.
-
Acopian Technical Company
These versatile DC-DC Converters are ideally suited for powering a wide variety of analog and digital circuitry, such as op amps, logic and microprocessors. They may be mounted directly on a printed circuit board for OEM applications, or installed in a socket for developmental and small quantity requirements.
-
PSM-101 -
Syscomp Electronic Design Ltd.
The PWM-101 is an adjustable DC power supply. The unique touch controls allow adjustment of the output voltage and current limit. This portable device is short circuit and thermally protected. An optional USB interface allows control of the power supply from a computer.
-
ROM-Elektronik GmbH
The DualField 1 sets new standards in measurement technology for low-frequency alternating fields. Professional measuring technology was realized with a worldwide unique price-performance ratio. This was made possible by the consistent use of innovative circuit elements and the most modern manufacturing processes.
-
TC 1.3kW to 3.5kW -
ET System Electronic GmbH
*Inverters up to 3500 VA*Quartz stabilized output ± 0.5%*Overload capacity up to 300%*Intelligent standby circuit*Adjustable load detection*EMC tested according to EN 61000-6-3 / 61000-6-1*Modified versions on request
-
OLS Series -
EIIT, S.A.
Developed as an economical and versatile solution, it adapts to any offline test application - ICT (In Circuit Test), ISP (Flashing) or FCT (functional). The design of this solution allows the quick and ergonomic change of fixtures , with a change time of less than 3 minutes.
-
Test Connections Inc.
TCI can furnish grid spring probes for most Bare Board Electrical Testers in production at most Printed Circuit Board Manufactures. Look for your model of Bare Board Tester in the following list and call TCI for current price quotation.
-
YB4360 -
KILTER ELECTRONIC CO.,LTD
High Sensitivity, Upto 1mV/div. High Light Graduation. ALT MAG£¬Normal£¨¡Á1£©and MAG display alternative. INT£¬auto select CH1/CH2. TV Sync£¬new design TV trigger circuit, AF. Trigger Lock
-
HCL-5000KN+ -
MULTI MEASURING INSTRUMENTS Co., Ltd.
・Wide AC current measurements for 0.01A~500A.・Easy operation, Push to Open and Pull to Disconnect Mechanism.・Safe AC current measurements for high voltage circuit (AC80 to 7000V).・Auto power off function and Splash proof structure.